MixMaster (MK2-2410-BK)

Technical data:

Model: SM-9213

Nominal voltage: 220–240V~ 50/60Hz

Protection class: II

General safety instructions

Read the operating instructions carefully before using the device and keep them in a safe place along with the warranty certificate, proof of purchase, and, if possible, the packaging with its inner padding. If you pass this device on to someone else, please also include the operating instructions.

This device is intended solely for private use and its designated purpose. It is not suitable for commercial use. Do not use the device outdoors (unless specifically intended for this purpose). Keep it away from heat sources, direct sunlight, moisture (never immerse in liquids!), and sharp edges. Do not use the device with wet hands. If the device becomes damp or wet, disconnect it from the power supply immediately.

Always switch off the appliance and unplug it (at the plug, not the cable) before cleaning or storing it. Disconnect the appliance from the mains when not in use and remove any attached accessories.

Never operate the device unattended. When you leave your workstation, switch the device off or unplug it (always pull on the plug, not the cable).

Regularly inspect the device and cable for damage. Do not use it if it is damaged. Do not attempt to repair the device yourself. Always contact an authorized technician. To avoid hazards, a defective cable must only be replaced by the manufacturer, our customer service department, or a qualified professional, and only with an equivalent cable.

Use only original spare parts.

Please be sure to observe the following “Special Safety Instructions”.

• Place the iron vertically
  
• Plug in
  
• Steam regulator set to “MIN”
  
• Preheat until the light goes out.
  

Now you can iron it dry.

Children and people in need of assistance

To ensure the safety of your children, keep all packaging materials (plastic bags, cardboard boxes, polystyrene, etc.) out of the reach of children.

Warning! Do not let small children play with foil – risk of suffocation!

This device must not be used by children. Keep the device and cable out of the reach of children.

This device is not a toy. Children must not play with it.

The device may only be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they are supervised or have been instructed in the safe use of the device and understand the potential hazards.

Special safety instructions for this device

Always disconnect the device from the mains power supply when it is left unattended, and before assembling, disassembling or cleaning it.

Switch off the device and disconnect it from the mains power supply before changing accessories or approaching moving parts during operation.

Use the device only as intended.

CAUTION: To avoid hazards from unintentional resetting of the thermal shutdown, this device must not be operated via an external switching device such as a timer or connected to a circuit that is regularly switched on and off by the electricity supplier.

• Operate the device only under supervision.
  
• Do not tamper with safety switches.
  
• Do not touch any rotating hooks or parts during operation.
  
• Only place the device on a smooth, flat and stable work surface.
  
• Only plug the power cord into the socket once all necessary accessories are correctly installed.

Parts overview:

2. Mixing bowl 3. Dough hook 4. Dough hook with silicone coating 5. Flat stirrer 6. Bracket for bowl cover 7. Bowl cover – top plate 8. Bowl cover 9. Whisk

10. Drive shaft 11. Swivel arm 12. Release button 13. Rotary control (speed) 14. Power cable 15. Suction cup

Gearbox setting

0 position – Stop (standby mode) Stage 1–6 – Cruise control Level 1 – slowest speed Level 6 – highest speed P position – pulse operation / highest speed for a short time

Instructions for use:

Please do not use the hook for more than 2.5 kg of dough.

Cleaning instructions

Unplug the power cord before cleaning.

Never immerse the motor housing in water!

Do not use harsh or abrasive cleaning agents.

engine housing

Simply wipe the outside with a damp cloth.

Mixing bowl and accessories:

All parts that have come into contact with food can be cleaned with soapy water.

Allow all parts to dry completely before reassembling the device. After drying, if necessary, lightly apply a small amount of vegetable oil to the surfaces (e.g., graters/sieves).

Assembly instructions

Caution:

Please attach the accessories correctly according to the assigned position in the table.

Directions:

	Place the machine on a level surface. surface, e.g. a kitchen worktop, and make sure that the suction foot (15) is on the underside and correctly on the surface The contact surface of the suction foot (15) must be free of water stains. or dirt, to prevent a decrease in adhesive strength.
	Turn the release button (12) with your right hand while holding it with the swivel arm with the left hand (11) hold it until the swivel arm (11) can no longer be lifted. Then the release button (12) Slowly release your right hand so that it naturally returns to its normal position.
	Attach the bowl cover (8) on the swivel arm (11) accordingly the illustration.
	Place the ingredients in the mixing bowl. (2) Place the bowl as shown in the Image shown and rotate it counterclockwise until it clicks into place.
	Choose the appropriate option depending on the ingredient. Accessories: Dough hook (3), flat beater (5) or whisk (9) – and attach it to the drive shaft (10). Align the center hole of the accessory with the drive shaft (10) Turn it off, push it upwards and turn it. it counterclockwise until it clicks into place on the stirring stick. Make sure that... that the accessory is securely attached.
	Turn the release button (12) clockwise with the right Hand, simultaneously hold the swivel arm (11) with your left hand and Press the swivel arm (11) as shown. shown downwards in the image – the The machine is now ready for use.
	When the work process is complete, set the speed control (13) to “0”. Pull the power plug when disassembled or when not in use.
	Turn the mixing bowl (2) clockwise to remove it. Turn the accessory clockwise to remove it. Remove the bowl cover in Arrow direction.

• Check that the plug is properly inserted into the socket.
  
• Check if the rise button has returned to its correct position.
  
• Check if the machine has been running for more than 6-10 minutes and wait until the motor has cooled down.
  

Problem:

Noises in the mixing bowl during operation (accessories rubbing against the bowl)

Solution:

• Check that the mixing bowl is correctly inserted.
  
• Check that the accessories are properly attached to the machine.
  

Problem:

The lid doesn't fit properly on the mixing bowl.

Solution:

• Check that the lid is correctly fitted.
  
• Check that the mixing bowl is correctly inserted and locked.
  

Problem:

The machine does not work at certain speed levels.

Solution:

• Check that the marking on the speed control matches the label on the housing.
• Turn the dial to "0" and check again if the device is working.
  

Problem:

The machine moves during operation

Solution:

• Check if the anti-slip feet have fallen off.
  
• Check that the machine is standing on a smooth and level surface.
  

Problem:

The lifting button does not spring back after the bowl and lid are inserted.

Solution:

• Check that the lid is correctly fitted.
  
• Check that the mixing bowl is inserted correctly.
  
• Check that the marking on the speed control matches the label on the housing.
• Turn the dial to "0" and check again if the device is working.
  

Problem:

The machine moves during operation

Solution:

• Check if the anti-slip feet have fallen off.
  
• Check that the machine is standing on a smooth and level surface.

Problem:

The lifting button does not spring back after the bowl and lid are inserted.

Solution:

• Check that the lid is correctly fitted.
  
• Check that the mixing bowl is inserted correctly.

Electrical circuit diagram